BK Precision 9130 Bedienerhandbuch

Model 9130 Triple Output Programmable DC Power Supply INSTRUCTION MANUAL MODEL 9130

10 14) Verify channels 2 & 3 according to steps 1) – 8) 5．If the Power Supply Does Not Turn On Use the following steps to help resolve problem

11 arrow on the handle and the arrow on the plastic ears are in opposite directions. Now you can pull the handle outwards. After removing the handle,

12 3. Specifications 3.1 Specifications Parameter 9130 Output ratings Voltage 0~30V×2, 0~5V×1 Current 0~3A×2, 0~3A×1 LVP* 0~31V×2, 0~6V×1 Load Regul

13 8.45in(W) x 3.8in(H) x 13.9in(D) *) LVP: Limit Voltage Protection. Limits the voltage than can be set either via the front panel or remote con

14 4. Front-panel Operation So far we have covered the quick start chapter which briefly introduced the front panel operation and how to check basic

15 4.2 Panel Description 41 27536Esc0●98RecallMenuEnterV-setV-setI-setI-setSaveOn/Off 0～9

16 4.4 Menu Descriptions Press Menu to indicate operation mode. View the menu on the VFD, and use the keys or the knob to scroll through the com

17 Power SN display the serial number Soft Version Display the firmware version Cal Information Error Information Exit Exit Menu 4.5 Pan

18 Solution 2: Press V-setV-set, then use the arrow keys to move the cursor to the desired position and adjust the value with the knob. (Make sure

19 Press Recall followed by a number 1 – 50 to recall operating state assigned to this location. You can also use the SCPI command:*SAV、*RCL to sav

2 Safety information Please review the following safety precautions before operating our equipment. General information The following safety precaut

20 Baud Rate Set This parameter configures the baud rate for serial communication. Possible values are 4800，9600，19200 or 38400. When operating

21 Out Series Set This function configures the instrument for series operation of 2 channels. “None” means that each channel operates independently

22 Connection diagram example: Channels 1 and 2 connected in parallel Note: When configuring for series or parallel operation, the user must w

23  Power Information The following menus provide information about the specific power supply unit. Power Model: the model of power supply For exam

24 5. Remote Operation The DB9 interface connector on the rear panel of the power supply can be connected to a RS-232 or USB interf

25 5.2 Communication between Power Supply and PC Before putting the instrument into remote operation, make sure that the baud rate, parity bit and c

26 5.3 SCPI Command Overview 5.3.1 Common IEEE488.2 commands *CLS *ESE *ESE? *ESR? *IDN? *OPC *OPC? *PSC *PSC? *RST *SRE *SRE

27 CONDition? INSTrument [:SELect] {FIRst|SECOnd|THIrd} [:SELect]? NSELect {1|2|3} NSELect? OUTPut [:STATe] {0|

28 :RWLock DISPlay: [:WINDow][:STATe] {OFF|ON} [:WINDow][:STATe]? MEASure[:SCALer] :CURRent[:DC]? [:VOLTage][:DC]?

29 APPly:CURRent[:LEVel][:IMMediate][:AMPLitude]? This command is used to read out the 3 channels’ current setting value at the same time. Parameter

3 TABLE OF CONTENTS 1. INTRODUCTION ...

30 MEASure[:SCALar]:POWer:ALL[:DC]? This command is used to read out the measured output power value of the 3 channels simultaneously. Parameter type

31 The Structure of the condition register is as followed: condition event enable condition

32 5.4.2 SCPI Command Description Common IEEE488.2 Commands *CLS This command clears the following registers：  Standard event status register

33 VX. XX software version number For example: BK PRECISION, 9130, 000000000000111101,V1.66 *OPC When all commands sent t

34 parameters include constant current, constant voltage, maximum voltage value and step voltage values. Command syntax: *SAV Parameter: 0~

35 Example: SYST:RWL SYSTem:ADDRess This command reads the communication address of the power supply. Command syntax: SYSTem:AD

36 Parameter: 0~255 Reset value: consult PSC command Example: STAT:OPER:ENAB 110 STATus:OPERation:ENABle? This command querie

37 STATus:OPERation:INSTrument:CONDition? This command queries parameters from operation condition sub register. After this command is executed, th

38 Parameter: 0~999999S (if you set 0S,the output-timer will be disabled.) Reset value: It is concerned about the parameter you set in the

39 [SOURce:]VOLTage:PROTection[:LEVel][:IMMediate][:AMPLitude] This command sets the max. voltage for the current channel. Command syntax: [SO

4 6.5 Test sequence generation ... 44 6.5.1

40 6. PV9130 Software Guide 6.1 Introduction PV9130 is a software application for the 9130 Triple Output Programmable DC Power Supply. To use this

41 1234567891011 1 Configure the software operating parameters and serial communication parameters. 2 Voltage chart 3 Voltage and current d

42 6.3.1 Save and Open Save the program, Quick Set, voltage sweep and GO/NG settings to a PAR file. Open the program, Quick Set, voltage sweep a

43 6.3.3 Status bar The status bar will give you the communication information. When communication is successful, the status bar will display the fol

44 6.4.2 Setting Voltage and Current Before setting voltage/current values, you need to select a channel. If you want to set voltage and current for

45 Voltage Sweep Before this operation, please select the channel you need： . Enter parameters StartValue, StopValue, voltageStep and Delay. Press

46 [left intentionally blank]

47 Service Information Warranty Service: Please return the product in the original packaging with proof of purchase to the address be

48 22820 Savi Ranch Parkway Yorba Linda, CA 92887 www.bkprecision.com © 2014 B&K Precision Corp. V060214 Print

5 1. Introduction Description The 9130 is a fully programmable triple Output DC Power Supply delivering 0-30V/0-3A on 2 outputs and 0-5V/0-3A on 1 o

6 2. Quick Start This chapter will help you getting acquainted with the front panel operation of this power supply. 2.1 Front & Rear Panel Front

7 Rear Panel 1 2 3

8 2．Connect the power cord and turn on the power supply When you turn on the power supply, the front-panel display will light up briefly while the po

9 Note: “X” denotes the channel for which calibration data was lost. If the calibration data in the EEPROM is corrupted or the factory calibration v