Bk-precision 4078 - Manual Bedienungsanleitung Seite 25
- Seite / 103
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Marker Function Illustration
F4: EDIT - Refer to section 3.6.4 below for details.
**Changing one of the arbitrary parameters as start and length causes an update of the output waveform to the new
parameters. When exiting the Arbitrary Menu by selecting a different waveform, a message to save the Arbitrary
wave will be displayed. Select YES or NO to save the new waveform. This save functions the same as the SAVE
ARB function.
F3: AMPL/OFST - Selects the Amplitude or Offset parameter.
In Arbitrary mode, this setting defines the maximum peak-to-peak amplitude of a full-scale
waveform. If the waveform does not use the full scale of data (-8191 to +8191), then its
actual amplitude will be smaller.
- Selects the Offset parameter. Change the offset by using the cursor keys, rotary knob or
numerical keypad. If a certain setting cannot be produced, the waveform generator will
display a “Setting Conflict” message.
F4: INTCLK/EXTCLK - Selects between using the internal clock or external clock.
For Model 4078 only:
For the 4078 with dual channels, channel 1 (CH1) is the MASTER channel. If selected
for external clock (EXTCLK), the same clock will also be applied to channel 2 (CH2) if
EXTCLK is also selected in CH2. (Note: There is only one BNC connector for external clock
input, which is common to both channels)
Start Address
Length
Markers
0
5 V
Arbitrary waveform
from front panel
channel output
5 V TTL signal
output from rear
Marker Out connector
- Safety Summary 3
- Table of Contents 5
- Section 1 7
- Specifications 8
- Modulation Combinations 10
- Section 2 11
- 2.6 Power Requirements 12
- 2.7 Grounding Requirements 12
- 2.8 Signal Connections 12
- 2.9 RS-232 Connection 12
- 2.11 GPIB Address 13
- 2.10 RS-232 Configuration 13
- Section 3 15
- 3.2 Display Window 16
- 3.3 Front Panel Controls 17
- 3.4 Back Panel Controls 17
- 3.5 Output connectors 18
- 3.6 MENU Keys 18
- 3.6.1 WAVEFORM Keys 20
- 3.6.2 MODE Key 22
- 3.6.3 ARBITRARY Key 23
- Start Address 25
- Markers 25
- 3.6.4 Arbitrary EDIT Menu 26
- 3.6.5 PULSE Menu 29
- 3.6.6 UTILITY Key 29
- 3.6.8 MODULATION Key 32
- 3.7 ON Key 34
- 3.8 Cursor Movement Keys 34
- 3.9 Rotary Input Knob 34
- 3.10 Power-On Settings 34
- 3.11 Memory 35
- 3.12 Displaying Errors 35
- 3.14 Examples 36
- 3.14.6 Using Voltage Offset 39
- 4.1 Overview 40
- 4.2 Device State 41
- 4.4 Device Address 41
- 4.5.1 The Input Buffer 42
- 4.5.2 The Output Queue 42
- 4.5.3 Response Messages 42
- 4.5.4 Coupled Commands 42
- 4.6 Block Data (GPIB Only) 43
- 4.8 Instrument Reset 43
- 4.9 Self Test 43
- 4.10 Command Syntax 43
- 4.11 Status Reporting 47
- 4.11.4 The Error Queue 48
- 4.11.5 Error Codes 48
- 4.12 Common Commands 51
- 4.13.1 SOURce Subsystem 55
- 4.13.1.2 Amplitude 57
- 4.13.1.3 Offset 57
- 4.13.1.5 Function 58
- 4.13.1.6 Point Rate 59
- 4.13.1.7 AM modulation 59
- 4.13.1.8 FM modulation 61
- 4.13.1.9 FSK modulation 62
- 4.13.1.10 Sweep control 64
- 4.13.1.11 PHASe adjust 66
- 4.13.1.12 PULSe setting 66
- 4.13.1.13 Duty Cycle 67
- 4.13.2 OUTPut Subsystem 68
- 4.13.2.1 Output State 68
- 4.13.3 Trigger Subsystem 68
- 4.13.3.1 Trigger Mode 69
- 4.13.3.2 Trigger Source 69
- 4.13.3.3 Burst Count 69
- 4.13.4 Arbitrary Subsystem 70
- 4.13.4.1 Point Rate 71
- 4.13.4.2 Address 71
- 4.13.4.3 Data 72
- 4.13.4.4 Line Draw 73
- 4.13.4.5 Clear 73
- 4.13.4.6 Copy 74
- 4.13.4.10 Start Address 76
- 4.13.4.11 Wavelength 76
- 4.13.4.12 Marker Address 76
- 4.13.4.13 Marker Length 77
- 4.13.4.14 Marker State 77
- 4.13.4.15 Save 77
- 4.13.5 Status Subsystem 78
- 4.13.5.1 Status Preset 78
- 4.13.5.2 Error Queue Read 78
- 4.13.5.3 Error Queue Enable 78
- 4.13.6 System Subsystem 81
- 4.13.6.3 SCPI Version 82
- 4.13.6.4 Security 82
- 4.13.6.5 Power-on Buffer 82
- 4.14.2 DCL - Device Clear 83
- 4.14.4 LLO - Local Lockout 83
- 4.15 SCPI Command Tree 84
- 4.15.4 :TRIGger Subsystem 85
- 4.15.5 :ARBitrary Subsystem 85
- 4.15.6 :STATus Subsystem 86
- 4.15.7 :SYSTem Subsystem 86
- 4.17.1 General 90
- Section 5 94
- 5.3 Performance Tests 95
- 5.3.3 Offset Accuracy 97
- 5.3.4 Sine Distortion 97
- 5.3.7 Operating Modes 98
- 5.3.10 RS232 Capability 100
- Performance Tests Results 101
Verwandte Produkte und Handbücher für Generatoren Bk-precision 4078 - Manual
(110 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern